#HONEYWELL ALARM KEYPAD BATTERY CHANGE HOW TO#
#HONEYWELL ALARM KEYPAD BATTERY CHANGE CODE#

To reconnect the front side of the motion detector, hook the hinge side and push down until it snaps shut.

Make sure to align the positive and negative sides of the battery correctly.

Replace the old battery with a new battery.

This device uses a lithium CR123 battery.

The base of the detector will remain on the wall and the front will be removed.

Locate the slot at the bottom of the device and push your screwdriver into the slot to open the device.

This device will likely be mounted in a corner on the wall of your home. Changing a Honeywell Wireless Motion Detector

After changing the batteries on your alarm devices, you will need to disarm your alarm system twice.ī.

Your device battery should now be changed.

To put the cover back on, hook the hinge side and push to close, making sure the cover snaps back in place.

There is a tamper switch on the device that will indicate trouble on your keypad if the cover is not put correctly.

Put the new battery in, making sure your positive and negative sides are correctly lined up.

Remove the old battery, which is a lithium CR123 Battery.

You will need to depress the tab with the screwdriver to allow the cover to come off.

The 5816 Wireless contact will have an arrow on the cover pointing towards the tab.

Mot often the most difficult part of changing batteries is removing the cover.

After locating the device, use a flat blade screwdriver to open the device.

When your device battery is low, your keypad will begin to beep to notify you that the device’s battery is low.

Changing Batteries on Honeywell Alarm Devices

View Alarm Grid’s video Honeywell 5800C2W: Fixing a Cover Tamper. If the tamper on the device whose tamper is being manually held down does not clear, then you can assume it is a defective tamper switch. At the panel or keypad, perform a disarm sequence twice. The device should be restored, meaning if it's a door/window contact using a magnet, the magnet should be next to the transmitter in the 'closed' position.ģ. It may be easier to do this if you remove the transmitter from its mounting location, and hold it in your hand. Press and hold the tamper switch down with your thumb or finger. If the cover is still on the device, remove it. To test the device and verify that the tamper is working correctly, follow these steps:ġ. This is usually caused by the cover tamper not fitting on the transmitter quite right. On rare occasions, a wireless device may have a malfunctioning tamper switch. You can also press the Home Key once or twice, until you're provided with a number pad, then enter your valid 4 digit code.

With Lynx or Lyric alarm panel, go to Security > Disarm > Enter Code.

#HONEYWELL ALARM KEYPAD BATTERY CHANGE CODE#

With Vista panels, this means entering your 4 digit code + Off. Once the reason for the tamper is found and corrected, whether it was a panel tamper, or a sensor tamper, disarm the system again to clear the tamper display. AiO panels may have multiple tampers, one for the front or back cover, and one for the bay where the communicator is installed.

Usually, a tamper is due to the cover not being placed back on the device correctly, or in some cases, if the sensor has a back tamper, it may not be mounted correctly, or may be missing its back mounting plate. Wired panels installed in commercial locations often have a cover tamper added to the metal panel enclosure lid and tied to a wired zone.

Tamper switches are usually only present on All-in-One (AiO) alarm panels, wireless devices, life safety devices such as smoke detectors or carbon monoxide detectors, and expansion modules. A base or back tamper ensures that if a device is removed from its mounting location, the end-user is made aware of it. A cover tamper ensures that if the cover is removed from a device, the end-user is alerted to that fact. There are two different types of tampers cover tamper, and base or back tamper. Once the cover is on, disarm again to clear the message from the display. This could be a loose cover on the system itself, a wireless device or a module. Next, find the cause of the tamper and correct it. When a tamper occurs, the first step is to perform a disarm to quiet the trouble sound.

#HONEYWELL ALARM KEYPAD BATTERY CHANGE HOW TO#

How to clear a Tamper on a wire:wireless system

Honeywell alarm keypad battery change